首頁

金屬氟碳漆

Metal Fluorocarbon Paint

主要用于室內外、混凝土及墻璧紙裝修及保護。

關鍵字：

金屬氟碳漆

所屬分類 Category：

氟碳漆

Fluorocarbon paint

咨詢熱線 Tel：

13805008562

在線咨詢 Online consultation

產品詳情 Description

產品說明:

金屬氟碳漆是由性能優異的氟碳樹脂為主要成份的環保型單、雙組份氟碳涂料，具有出色的耐候性、保色性、易施工、易清潔及長期優異的保光、保色性能。

產品用途:

外墻高檔涂料,廣泛用于別墅、酒店、橋梁、體育館鋼構、賓館等高檔建筑外墻裝飾、屋頂及各種建材的耐久性裝飾保護涂層。

施工步驟;
1、施工前除去基層表面松動的灰、沙土、油污、水份及其他附著物。

2、施工材料:氟碳金屬漆。為保證質量,產品出廠時已將粘度調到適合施工的粘度,現場不再稀釋。

3、施工道數:氟碳金國面涂1-2道。配專用輒碳底漆噴1-2道。氟碳金屬漆在施工時,每道宜薄噴,走槍勻速,涂膜均勻一致,杜絕發花現象;

4、施工方式:采用噴涂方式施工;

a.空壓機:壓力0.8-1.OMPa,排氣量>0.6m31分鐘以上;

b.噴槍:應選用性能可靠,并對出料量、風量、風壓可以進行調節的噴槍,以滿足需要;

5、姐碳外墻漆涂層厚度通常約為30-50微米。要求顏色均勻一致,不得有漏涂、發花、厚薄不均勻等現象;

6、氟碳外墻漆涂層檢哈合格后,即可下道工序(上罩光油);

7、描分隔(格)終,B小排管林卻寧楊色的專用洽料,小心地給縫描上顏色,使其既關觀又有保護分隔(格)縫的作用;

涂層養護:
涂裝施工后、5天內不許人法損你淪民,而漆涂層千燥后，應及時清垢、自松書修補-洽層養護時間應達7天以上。

施工方法:
可以滾涂、刷洽噴論這淪M里只住施工溫度不得低于5℃

稀釋配比:
如需稀釋,加入聯粒景不招討5/社在施工前攪拌均勻。涂刷面積:
理論面積4-5m²/kg（一遍）實際用量應視基面粗糙及具體操作而定。

Product Description:
Metal fluorocarbon paint is an environmentally friendly single and dual component fluorocarbon coating mainly composed of high-performance fluorocarbon resin. It has excellent weather resistance, color retention, easy construction, easy cleaning, and long-term excellent light and color retention performance.

Product Usage:
High grade exterior wall coatings are widely used for exterior wall decoration, roof decoration, and durability protection coatings of various building materials in high-end buildings such as villas, hotels, bridges, gymnasium steel structures, and hotels.

Construction steps：
1. Remove loose ash, sand, oil, moisture, and other attachments from the surface of the base layer before construction.
2. Construction material: fluorocarbon metal paint. To ensure quality, the viscosity of the product has been adjusted to a suitable viscosity for construction before leaving the factory, and it will not be diluted on site.
3. Number of construction layers: 1-2 layers of fluorocarbon gold national surface coating. Spray 1-2 coats of specialized carbon primer. During the construction of fluorocarbon metal paint, each layer should be sprayed thinly, with a uniform gun speed and uniform coating film to prevent blooming;
4. Construction method: Spray coating method is used for construction;
a. Air compressor: pressure 0.8-1.OMPa, displacement>0.6m31 minutes or more;
b. Spray gun: A spray gun with reliable performance and adjustable discharge volume, air volume, and air pressure should be selected to meet the needs;
5. The thickness of the carbon exterior wall paint coating is usually about 30-50 microns. The color should be uniform and consistent, and there should be no omissions, hairlines, uneven thickness, or other phenomena;
6. After passing the inspection of the fluorocarbon exterior wall paint coating, the next process (covering with varnish) can be carried out;
7. At the end of the partition (grid), the B small row pipe is made of a special material in the color of Que Ning Yang. Carefully color the seam, making it both visually appealing and protective of the partition (grid) seam;

Coating curing:
After the coating construction, no one is allowed to damage you or your people within 5 days. However, after the paint coating is dry, it should be cleaned and repaired in a timely manner. The maintenance time for the coating should be more than 7 days.

Construction method:
Rolling coating, brushing, and spraying are allowed. However, the construction temperature should not be lower than 5 ℃

Dilution ratio:
If dilution is required, add Lianlianjing and do not require 5% mixing before construction. Coating area:
The theoretical area is 4-5m2/kg (once), and the actual dosage should depend on the roughness of the base surface and the specific operation.

無